View PI3L301D_597495.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PI3L301D
3.3V, 16-Bit to 8-Bit, Mux/DeMux Gigabit Ethernet LAN Switch with Single Enable
Features
* * * * * * * * * * * RON is 4 typical Low bit-to-bit skew: 200ps Low crosstalk: -27dB @ 250MHz Low Current Consumption: 20A Near-Zero propagation delay: 250ps Switching speed: 9ns Channel On-Capacitance: 9.5pF (typical) VCC Operating Range: +3.0V to +3.6V ESD >2000V . . . Human Body Model >350 MHz bandwidth (or data frequency) Packaging (Pb-free & Green available): 48-pin 240 mil wide plastic TSSOP (A) 48-pin 173 mil wide plastic TVSOP (K)
Description
Pericom Semiconductor's PI3L series of logic circuits are produced using the Company's advanced sub-micron CMOS technology, achieving industry leading performance. The PI3L301D is a 16- to 8-bit multiplexer/demultiplexer LAN Switch. Industry leading advantages include a propagation delay of less than 250ps, resulting from its low channel resistance and I/O capacitance. The device multiplexes differential outputs from a Gigabit Ethernet transceiver (PHY) device to one of two corresponding B1 or B2 outputs. The switch is bidirectional and offers little or no attenuation of the high-speed signals at the outputs. It is designed for low bit-to-bit skew, high channel-to-channel noise isolation and is compatible with various standards, such as 10/100/ 1000 Base-T (Ethernet). Generally, this part can be used to replace mechanical relays in low-voltage LAN applications that interface a physical layer over CAT 5 or CAT 6 unshielded twisted pair cable through an isolation transformer.
Applications
* Dual Physical Layer Device sharing to one interface connector * SONET OC-12(622Mbps) signal routing * Routes physical layer signals for 10/100/1000 Mbit Ethernet
Pin Description
V DD A0 GND A1 GND V DD GND A2 GND A3 GND V DD GND NC A4 GND A5 GND V DD GND A6 GND A7 SEL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25
0B1 1B1
Block Diagram
A0 A1
0B1 1B1 0B2 1B2
GND
0B2 1B2
GND
2B1 3B1
A2 A3
2B1 3B1 2B2 3B2
GND
2B2 3B2
GND V DD
4B1 5B1
A4 A5
4B1 5B1 4B2 5B2
GND
4B2 5B2
A6 A7
6B1 7B1 6B2 7B2
GND
6B1 7B1
GND
6B2 7B2
SEL
1
PS8665B
07/22/03
PI3L301D 3.3V, 16-Bit to 8-Bit, Mux/DeMux Gigabit Ethernet LAN Switch with Single Enable Maximum Ratings Truth Table
Function AN to NB1 AN to NB2 SEL L H
(Above which useful life may be impaired. For user guidelines, not tested.) Storage Temperature....................................-65C to +150C Supply Voltage to Ground Potential...............-0.5V to +4.0V DC Input Voltage............................................-0.5V to +5.5V DC Output Current......................................................120mA Power Dissipation...........................................................0.5W
Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
2
PS8665B
07/22/03
PI3L301D 3.3V, 16-Bit to 8-Bit, Mux/DeMux Gigabit Ethernet LAN Switch with Single Enable DC Electrical Characteristics for 1000 Base-T Ethernet Switching over Operating Range
(TA = -40C to +85C, VCC = 3.3V 10%) Paramenter VIH VIL VIK IIH IIL IOFF RON RFLAT(ON) RON Input HIGH Voltage Input LOW Voltage Clamp Diode Voltage Input HIGH Current Input LOW Current Power Down Leakage Current Switch On-Resistance(3) On-Resistance Flatness(4) On-Resistance match from center ports to any other port(4) Description Test Conditions Guaranteed HIGH level Guaranteed LOW level VCC = Max., IIN = -18mA VCC = Max., VIN = VCC VCC = Max., VIN = GND VCC = 0V, VA = 0V, VB 3.6 VCC = Min., 1.5V VIN VCC, IIN = -40mA VCC = Min., VIN @ 1.5V and VCC, IIN = -40mA VCC = Min., 1.5V VIN VCC, IIN = -40mA Min. 2 -0.5 Typ.(2) -0.7 4 1 0.9 Max. Units 0.8 -1.2 5 5 5 8 2 A V
DC Electrical Characteristics for 10/100 Base-T Ethernet Switching over Operating Range
(TA = -40C to +85C, VCC = 3.3V 10%) Paramenter VIH VIL VIK IIH IIL IOFF RON RFLAT(ON) RON Input HIGH Voltage Input LOW Voltage Clamp Diode Voltage Input HIGH Current Input LOW Current Power Down Leakage Current Switch On-Resistance(3) On-Resistance Flatness(4) Description Test Conditions Guaranteed HIGH level Guaranteed LOW level VCC = Max., IIN = -18mA VCC = Max., VIN = VCC VCC = Max., VIN = GND VCC = 0V, VA = 0V, VB 3.6 VCC = Min., 1.25V VIN VCC, IIN = -10mA to -30mA VCC = Min., VIN @ 1.25V and VCC, IIN = -10mA to -30mA Min. 2.0 -0.5 Typ.(2) -0.7 1.0 0.9 Max. Units 0.8 -1.2 5 5 5 8 2.0 A V
On-Resistance match from center ports VCC = Min., 1.25V VIN VCC, to any other port(4) IIN = -10mA to -30mA
3
PS8665B
07/22/03
PI3L301D 3.3V, 16-Bit to 8-Bit, Mux/DeMux Gigabit Ethernet LAN Switch with Single Enable Capacitance (TA = 25C, f = 1MHz)
Parameters(4) Description Input Capacitance Port B Capacitance, Switch OFF A/B Capacitance, Switch ON VIN = 0V Test Conditions Typ. 3.1 2.8 9.5(5) Max. 3.6 6.0 10.9 pF Units CIN COFF(B1, B2) CON(A/B)
Notes: 1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V, TA = 25C ambient and maximum loading. 3. Measured by the voltage drop between A and B pins at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the two (A & B) pins. 4. This parameter is determined by device characterization but is not production tested. 5. Measured on worst case corner pin.
Power Supply Characteristics
Parameters ICC Description Quiescent Power Supply Current
Test Conditions(1) VCC = Max., VIN = GND or VCC
Min. -
Typ.(2) -
Max. 800
Units A
Notes: 1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V, TA = 25C ambient and maximum loading.
Dynamic Electrical Characteristics Over the Operating Range (TA=-40 to +85C, VCC=3.3V10%, GND=0V)
Parameter XTALK OIRR BW Description Crosstalk OFF Isolation Bandwidth -3dB Test Conditions f = 250MHz, See Fig. 2 f = 250MHz, See Fig. 3 CL = 10pf, See Fig. 1 Min. Typ.(2) -27 -32 350 Max. Units dB MHz
Switching Characteristics
Paramenter tPD tPZH, tPZL tPHZ, tPLZ tSK(o) tSK(p) Propagation Delay(2,3) Line Enable Time - SEL to AN, BN Line Disable Time - SEL to AN, BN Output Skew between center port (A4 to A5) to any other port(2) Skew between opposite transitions of the same output (tPHL - tPLH) (2) Description Test Min. Conditions 0.5 0.5 Typ. 0.1 0.1
(2)
Max. 15 9 0.2 0.2
Units
0.25 ns
Notes: 1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Guaranteed by design. 3. The bus switch contributes no propagational delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25ns for 10pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interactions with the load on the driven side.
4
PS8665B
07/22/03
PI3L301D 3.3V, 16-Bit to 8-Bit, Mux/DeMux Gigabit Ethernet LAN Switch with Single Enable Test Circuit for Electrical Characteristics(1)
6.0V VCC 200-ohm Pulse Generator VIN RT D.U.T VOUT 10pF CL 200-ohm
Notes: 1. CL = Load capacitance: includes jig and probe capacitance. 2. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator 3. All input impulses are supplied by generators having the following characteristics: f = 10MHz, ZO = 50, tR 2.5ns, tF 2.5ns. 4. The outputs are measured one at a time with one transition per measurement.
Switch Positions
Test tPLZ, tPZL (output on B-side) tPHZ, tPZH (output on B-side) Prop Delay 6.0V GND Open Switch
HP4396B
S
HP11667A
R
T
VCC
50-ohm 50-ohm 50-ohm
PI3L301D
CL = 10pF
Figure 1. Bandwidth -3db Testing
5
PS8665B
07/22/03
PI3L301D 3.3V, 16-Bit to 8-Bit, Mux/DeMux Gigabit Ethernet LAN Switch with Single Enable
HP4396B S HP11667A 50-ohm 50-ohm 50-ohm R
PI3L301D
100 -ohm
T
100 -ohm
Figure 2. Crosstalk Test Setup
HP4396B S HP11667A 50-ohm 50-ohm 50-ohm
100 -ohm
R
T
PI3L301D
Figure 3 . Off Isolation Tets Setup
6
PS8665B
07/22/03
PI3L301D 3.3V, 16-Bit to 8-Bit, Mux/DeMux Gigabit Ethernet LAN Switch with Single Enable Switching Waveforms
SEL
1.25V
2.5V 1.25V 0V
3.5V Input tPLH 2.5V 2.5V tPHL 2.5V 2.5V
Input A
tPZL
VDD/2
tPLZ
VDD
1.5V
VOL +0.3V
tPZH
tPHZ
VDD/2
VOL VOL VOL
Output
VOH
VOH -0.3V
Output A
VOL
Output B
tPZH
tPHZ
VOH
VDD/2
VDD/2
VOL
Voltage Waveforms Propagation Delay Times
3.5V Data In at Ax or Ay 2.5V tPLHX tPHLX
1.5V VOH
Voltage Waveforms Enable and Disable Times
3.5V Input tPLH tPHL 2.5V
1.5V VOH
2.5V Data Out at MBx
I tSK(o)
VOL VOH
Data Out at MBy
tPLHy tPHLy
2.5V
VOL
Output tSK(p) = I tPHL - tPLH I
2.5V
VOL
tSK(o) = I tPLHy - tPLHx I or I tPHLy - tPHLx I
Output Skew - tSK(o)
Pulse Skew - tSK(p)
Applications Information
Logic Inputs
The logic control inputs can be driven up to +3.6V regardless of the supply voltage. For example, given a +3.3V supply, the output enables or select pins may be driven low to 0V and high to 3.6V. Driving IN Rail-to-Rail(R) minimizes power consumption.
Power-Supply Sequencing
Proper power-supply sequencing is advised for all CMOS devices. It is recommended to always apply VCC before applying signals to the input/output or control pins.
Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd
7
PS8665B
07/22/03
PI3L301D 3.3V, 16-Bit to 8-Bit, Mux/DeMux Gigabit Ethernet LAN Switch with Single Enable Packaging Mechanical: 48-Pin TSSOP (A)
48
.236 .244
6.0 6.2
1
.488 12.4 .496 12.6
.047 1.20 Max
SEATING PLANE
.004 0.09 .008 0.20
0.45 .018 0.75 .030
X.XX X.XX
DENOTES DIMENSIONS IN MILLIMETERS
.0197 BSC 0.50
.007 .010
0.17 0.27
.002 .006 0.05 0.15
.319 BSC 8.1
Packaging Mechanical: 48-Pin TVSOP (K)
48
.169 .177
4.30 4.50
.0035 .008
1
.378 9.60 .386 9.80
0.09 0.20
.031 .041 0.80 1.05
0.45 .018 0.75 .030
.252 BSC 6.4
SEATING PLANE
X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS
.016 BSC 0.40
.0051 .009 0.13 0.23
.002 .006 0.05 0.15
Max. .047 1.20
8
PS8665B
07/22/03
PI3L301D 3.3V, 16-Bit to 8-Bit, Mux/DeMux Gigabit Ethernet LAN Switch with Single Enable Ordering Information
Ordering Code PI3L301DA PI3L301DAE PI3L301DK PI3L301DKE Package Code A A K K Package Description 48-pin 240 mil wide plastic TSSOP Pb-free & Green, 48-pin 240 mil wide plastic TSSOP 48-pin 173 mil wide plastic TVSOP Pb-free & Green, 48-pin 173 mil wide plastic TVSOP
Notes: 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/
Pericom Semiconductor Corporation * 1-800-435-2336 * www.pericom.com
9
PS8665B 07/22/03

▲Up To Search▲

Price & Availability of PI3L301D

	To Download PI3L301D Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .